What to Know Before Removing Old Trees

Sometimes a tree gets to the point where it is necessary to say goodbye to it. It can be a painful choice to make, but sometimes the tree gets too close to the house, gets too diseased, gets an incurable infestation of some pest, or grows too tall and gets close to a power line. If any of these things occur, it’s best to do the right thing and get rid of the tree. Although you might have spent hours and hours getting the tree to where it is today, it is almost dishonorable to the tree to allow it to suffer in bad conditions. Once you have made the choice to remove the tree, you need to plan its removal. I can’t begin to count how many windows I’ve seen knocked out or cars I’ve seen crushed because of poor planning in the tree removal process. Decide what direction you want it to fall, and accurately measure to make sure it will fall completely clear of anything else that it could possibly cause damage to. Once you have the falling direction planned out, you should climb up the tree and tie two long ropes near the top. Anchor them on the opposite side of the one that you want it to fall towards. This will allow you to adjust the direction the tree is being lowered in, just in case it starts leaning towards anything it could destroy. Now that you’ve taken all the necessary precautions, you are ready to begin chopping. If you plan on using a manually operated saw or ax, please step back and consider how insane that is.

Chopping down a tree by hand will take you forever, and will not even begin to be as accurate as using a chainsaw. If you don’t have a chainsaw, you shouldn’t even consider doing it without one. Ask around with your neighbors and see if anyone has one that you could borrow. If that doesn’t work, rent or buy one from your local home improvement store. Before you start chopping away at the tree, you should wear proper eye and face protection in case any wood chips fly towards your eyes. I had a friend who blinded his right eye while cutting down a tree, so I hope all of my readers do not make the same mistake as he did. Whenever you operate a power tool, always be sure to wear proper protection for any exposed parts of your body. When making the cut, you do not want to just cut a straight line into the tree. It is best to cut a sideways “V” into the tree. This is because if you cut the straight line, the tree will end up rolling to one side or the other.

If you cut in a “V”, the tree will be able to fall in the exact direction that you want it to fall. Occasionally it might be a few feet off due to human error during the cutting process, but if you have some strong friends pull on the ropes you tied, you can line it back up with the path you wanted it to take. The entire process shouldn’t take more than an hour. Removal of the stump can be slightly more difficult. You have several choices; you can rent out a stump chipper that will completely destroy the visible section of the stump. Or you can spend countless hours digging it out. Digging out the stump is much more thorough, but takes forever. If you’d prefer to skip this step you should check out this tree service jackson ms If you have kids this shouldn’t be a problem. Kids often find the thought of digging fun and are excited to go outside and dig all day long with their friends. This was the method I used, and I had the entire stump out within a week. Keep in mind that my stump was about 1 foot in diameter, and digging probably won’t work for stumps much larger than that.

Related News

Missing the permit for the trees: Congressional golf club cited for tree removal
The tony country club cleared four times the allowed amount of trees, according to Montgomery County officials….


UC Berkeley begins tree removal in People’s Park amid community dissent
UC Berkeley begins tree removal in People’s Park amid community dissent Daily Californian UC Berkeley began the removal of about 41 trees in ……


Family upset over memorial tree removal for West Chicago High construction project
The removal of a memorial tree at West Chicago Community High School has upset the family of a teenager who died more than 15 years ago….



Basic Guidelines for Cleaning Vinyl Siding

One needs less maintenance when making use of vinyl siding on your homes. However, at one point, you will be confronted with the task of cleaning it. It is not that difficult, but it would definitely take a good deal of your time. Doing this on your own will save you money, and will be a good way to evaluate the current condition of your vinyl siding. Cleaning vinyl siding is usually done by making use of a pressure washer or a power washer. One may buy one, or if possible rent one. In cleaning vinyl siding, use a mild soap or detergent if it is not that dirty yet. There are also detergents or cleaning solutions that have additives to help prevent problems like mold or mildew. Wear safety equipment like eye protection and gloves prior to the cleaning of your vinyl siding.

It is always better to be safe when doing such activities. Watch out for windows and doors during pressure washing. It is advisable to properly seal these portions. And be careful as well not to hit the ground as these may contribute to bringing dirt back to your sidings, and will mean a lot more work for you. When cleaning vinyl siding, make sure to start at the upper portion and then going down to the lower sections of the structure. Doing so will ensure that you will be doing your cleaning on a smooth and organized manner. You won’t have to go back and forth with your cleaning. Cleaning vinyl siding with green copper stains can be done by using a solution that contains oxalic acid and hot water. The granules for this acid can be bought at hardware stores.

A ¾ pound of the acid granules mixed with a gallon of hot water would be an ideal mixture. With your rubber gloves on and using a sponge, apply this solution on the stain and let it stay for around five minutes. After this, you may then scrub it off with the sponge or non-abrasive cloth. Repeat the process as necessary. Using a solution of bleach and water will do the trick when treating mold stains. For rust stains, there are special detergents available in the market today, specifically applicable for use in cleaning vinyl siding. Read the instructions carefully, and follow as per directions. Cleaning vinyl siding by pressure washing and with the appropriate cleaning solutions will help keep these in good condition. By doing so, your vinyl siding will begin to look clean and new again.

Brought to you by pressure washing Hattiesburg Ms

Related News

Cleaning Blogspot Spam: Is Google Responding to Public Pressure?
In Google! Clean Up Blogger! Now!, I wrote about how a simple search for a news story turned into a massive multi-page hunt through Google search ……


Hand Carry Electric Pressure Washer – take your cleaning to where you really need it
Things get really dirty outside so much so that just a normal hose often isn’t enough to get anything done. If you really want to get something ……